Видео

I sprayed break fluid all over the place because my line was kinked

Didn’t show how to install fuel pump?

Nice tutorial!

Why create a second channel?

Thank you!!!

I couldn't recall, did you mention to do this on a warm engine or from cold

Thank you sir

Do you know whats the number part for the clip that makes a bell noise when you put the key too the steering wheel ? By any chance?

Thank you ! 🙏🏼

I'm new to fixing cars and I was hoping to see how to disconnect the connectors from the ABS computer then that's the part the camera doesn't show😢

Those adjusters stop working long before the pads wear out. Then the a piston comes out to far, gets cocked & the brake drags overheating. You can hear the brakes at a complete stop hold up before releasing. Antiseize did not work good for me on the adjusters. The adjusting arm is flimsy jumps over the star wheel. Adjusting them is harder when the parts are not all new cause the drum hangs up. The whole system sucks.

Thank you for an easy to follow video. Mission accomplished!

penzoil or amsoil for me

omg you let it all dry on the paint your not suposed to do that

I’ve been doing the two man method a whole bunch of air came out then som fluid and then it seamed to completely stop. Did you do this with master cylinder cap on or off? I’m going to try it

new parking cable, and my parking brake still doesn't grab. watched at least half a dozen other videos, they all explained what to do, but didn't actually show it, so thank you! i'll update if worked.

Thank you ; I have been chasing this issue for years.

thank you ~ thank you ~ thank you ~ thank you ~ i really appreciate your video. restoring my 1993 Astro Van - i bought brand new in 1993. thank you ~ again

So, the "proper way" to adjust the idle is... Reset the IAC valve, then adjust the screw that you should not adjust to get the rpm at preferred rpm range . Got it

Do you know how I can disconnect the whole horn? Mine is stuck on when i turn the steering wheel. I removed the fuse but that caused other issues. I cant find the relay or wire inside the steering column. I already removed the wire from the steering wheel. 89 chevy silverado

How does the 4.0 runs with amsoil? Smooth or rough? Slow?

Hooking up the hoses back up looks like a bitch

I like the adapter, but $75? I think I'll stick to the universal adapter. "06 Tundra LTD AC here.

Nice job with the video..

You had air being sucked into the system somewhere higher up in the line or lines. The volume of the entire brake line system shouldn't be more that the bottle filling it. Hence the time and sudden cut to a screen stating it took an hour. True evidence of success would have been showing the submerged tube no longer pushing air and volume was still increasing before closing the bleeder.🙂

👏🏻👏🏻👏🏻

The same thing happened to me with the wheel cylinders! It is my own fault, I should have looked closer, I ordered the right part# but they were boxed wrong so now I have to do it all over again, thanks for the tips.

Is clutch fluid the same thing as brake fluid? It’s been a long time since I had a manual transmission, and I don’t remember.

The wix xp filter is actually a extremely coarse media, about 40 or 50 micron. Unfortunately wix doesn't advertise the micron rating for any of the xp filters that I have searched. If they offer a xe filter for that number that is the tightest filter that wix offers. Usually 15 micron and they do advertise ratings on the standard filters and xe.

where did you hook up the multi meter too

Thank you for making this video. I wish more people made videos like yours that show a more intelligent approach to replacing or repairing something. This video is the only one out of dozens I watched on this subject that demonstrated the intelligent use of tools. Every other video included beating the old parts out and they all used at least a little bit of tapping with hammers to most striking several hard blows with a hammer on their brand new part as well as their drive shaft. No wonder they all had issues with the universal joint not being quite as free moving as it should be. Thanks for showing us a better way!

Great way to do this. Please post more videos on NPR maintenance if you have any!

I was going to suggest using amsoil ATF on the next service. Lubegard also makes ATF that should work for your box truck.

Good Job. Explained how to do it well.

So what you should Have done. Was 2 replace the other clip and position the camera better? So we could see better. I'm just saying that's all.😊😊 But thank you

Can you lift a 2015 Jeep Grand Cherokee with this?

I love the ease of your instructions and was successful at doing it myself - thank you

So, just diconnect the sway bar mount, remove driven side flange bolts, remove hub nut, and put it back on the ground. Sway bar link/bushings weren't removed? Didn't get 10k miles out of my refurbished one. Boot split.

Is amsoil signature series 5w30 good for extreme cold weather?? Like -40m

Just completed this conversion, including filter housing gaskets (of course). Suggestion - plan to insert PTFE/CPE flex hose for at least lower housing inlet line. If you cut original lines at the extreme end of line (right before flare) you might be able to work it. Otherwise, you'll have issues with the short straights/bends. 1st cut didn't provide enough straight line section for fitting. Then cut line back to 2nd flat section (~1" further) and was able to get flare fitting on. But the line angle is not great and close to frame/transaxle. I consider this a workaround until I get a flex hose in there (which I had it to begin with).

You forgot a piece in your steering wheel. It's a big piece towards the end that needs to go back on there

Thank you! This went from me thinking i would be out there for hours, to being able to do it on my lunchbreak 😊

I have a missing rod on one side.

My rod pulled all the way out. Can't get tailgate open

Update???????

Our

Is

Where

I have a 4.3 and i was wondering if all the Blocks have the 2 tapped holes for the adapter to bolt to cause my remote system has to be bolted to block and im not sure if my block has the 2 holes i have seen some that doesent have them.

Thanks for posting this very helpful